保溫防爆墻門窗洞口邊框線，并放好頂龍骨位置邊線。裝門洞口框：放線后按設計，先將隔墻的門洞口框安裝完畢。裝龍骨：按分檔位置安裝豎龍骨，豎龍骨上下兩端插入沿頂龍骨及沿地龍骨，調整垂直及定位準確后，用抽心鉚釘固定，靠墻，柱邊龍骨用射釘或木螺絲與墻，柱固定，釘距為1000mm.。薄體輕質采向抽心鉚釘或螺栓固定。衛生設備和管道及開口位置。放出隔墻位置線在已做好的地面或地枕帶上防爆墻根據設計施工圖同時標出門窗標出沿頂(地)龍骨的位置防爆墻具有實心以達到節約能源裝橫向卡擋龍骨：防爆墻按照設計在地面及天棚彈線防爆墻：有金屬結構組成，具有抗沖擊波的能力，能將事故破壞作用限制在一定范圍內的墻。與纖維水泥復合鋼板防爆墻相比它具有重輕和易裝易卸可回收再利用等優點。

    保溫防爆墻以防降低鋼板防腐性，鉆孔可使用手電鉆，鉆頭采用高強度不銹鋼。防爆板一般無需保養，正常使用時，不會發生碰裂或老化現象，板材堅固而耐用，板材表面可以用清潔劑去除表面污潰。一般設置在玻璃鋼冷卻塔填料。底面鋪設防潮墊料存放地面應干澡平坦避免板角受到碰撞搬運時應托邊搬運防爆墻由雙面單層防火板和鍍鋅輕鋼龍骨體系內填巖棉構成。內側單層厚度為8毫米，外側單層厚度為12毫米。并做好防雨設施。在去除切口毛刺時應避免鋼板鍍鋅層受到破壞防爆墻可使用銼刀或砂輪機來除去因切割鋼板而鋒利的刃口。切口一般無需做防腐處理鍍鋅輕鋼龍骨體系由橫龍骨和豎龍骨構成，豎龍骨尺寸75x50/40x0.7mm，分布間距為407毫米，橫龍骨尺寸為75x50/40x0.7mm，分布間距為2440毫米，兩層防火板中間填充75毫米厚巖棉。